Page Comparison

1. Open the Angular menu on the 3D Document Toolbar. (Click the drop-down arrow to the right of the Linear icon to see the menu of commands.)
2. Select Three Points Angle.
3. Optional:
   1. Select Lock tool to use the command more than once.
   2. Enter a hyperlink to a file or to a document and user view within the current file.
4. Position your cursor on the first point and click. (Crosshairs appear when you mouse over a selectable point.) The selected point is yellow.
5. Select the second and third points. The second point will be the vertex point of the angle
6. Drag the label into position and click once.
7. Optional:
   1. Click Copy to copy the markup content to the Windows clipboard.
8. Click Stop when you're finished taking multiple measurements. Click Close (or X) to end the command and close the dialog box.

1. Open the Angular menu on the 3D Document Toolbar. (How? Click the drop-down arrow to the right of the Angular icon. You should see a drop-down menu listing the available commands.)
2. Select Two Edge Surfaces Angle to view the Two Edge Surface Angle Measurement dialog box.
3. Optional: If you want to measure more than one angle, select the Lock tool checkbox.Optional: Navigate to or enter
   1. Select Lock tool to use the command more than once.
   2. Enter a hyperlink to a file
   , an Internet page, a user view, or another document in the workspace.

Glen: When I use the browser, system crashes. How is this command used? When the other file is opened, do you then use Copy to transfer measurement info?

1. Click an edge
   1. or to a document and user view within the current file.
2. Click an surface on the model. The edge surface is highlighted when the pointer is properly positioned.
3. Click a co-planar edge another surface on the model.
   Note: The two surfaces chosen must be either two planar, non-parallel surfaces or one cylindrical and one planar surface.
4. Drag the label into position and click once.
5. Click Stop when you're finished taking measurements; at this point, you can still copy the most recent measurement to the WIndows clipboard. Select Close (or X) to end the command and close the dialog box.

1. Open the Angular menu on the 3D Document Toolbar. (How? Click the drop-down arrow to the right of the Angular icon. You should see a drop-down menu listing the available commands.)
2. Select Surface Point to Point Angle to view the Surface Point to Point Angle dialog box.
3. Optional: If you want to measure more than one angle, select the Lock tool checkbox.Optional: Navigate to or enter
   1. Select Lock tool to use the command more than once.
   2. Enter a hyperlink to a file
   , an Internet page, a user view, or another document in the workspace.

1. 1. or to a document and user view within the current file.
2. Click on a surface. A surface is highlighted when the pointer is properly positioned.
3. Click a point on the model. Red dots designate available points on the model. Crosshairs indicate when the pointer is properly positioned over a point.
4. Drag the label into position and click once.
5. Click Stop when you're finished taking measurements; at this point, you can still copy the most recent measurement to the WIndows clipboard. Select Close (or X) to end the command and close the dialog box.

1. Open the Angular menu on the 3D Document Toolbar. (How? Click the drop-down arrow to the right of the Angular icon. You should see a drop-down menu listing the available commands.)
2. Select Surface Point to Edge Angle to view the Surface Point to Edge Angle dialog box.
3. Optional: If you want to measure more than one angle, select the Lock tool checkbox.Optional: Navigate to or enter
   1. Select Lock tool to use the command more than once.
   2. Enter a hyperlink to a file
   , an Internet page, a user view, or another document in the workspace.

Glen: When I use the browser, system crashes. How is this command used? When the other file is opened, do you then use Copy to transfer measurement info?

1. 1. or to a document and user view within the current file.
2. Click on a surface of the model. A surface is highlighted when the pointer is properly positioned.
3. Click an edge on the model. The edge is highlighted when the pointer is properly positioned for selection.
4. Drag the label into position and click once.
5. Click Stop when you're finished taking measurements; at this point, you can still copy the most recent measurement to the WIndows clipboard. Select Close (or X) to end the command and close the dialog box.

1. Open the Angular menu on the 3D Document Toolbar. (How? Click the drop-down arrow to the right of the Angular icon. You should see a drop-down menu listing the available commands.)
2. Select Surface Point to Surface Point Angle to view the Surface Point to Surface Point Angle dialog box.
3. Optional: If you want to measure more than one angle, select the Lock tool checkbox.Optional: Navigate to or enter
   1. Select Lock tool to use the command more than once.
   2. Enter a hyperlink to a file
   , an Internet page, a user view, or another document in the workspace.

Glen: When I use the browser, system crashes. How is this command used? When the other file is opened, do you then use Copy to transfer measurement info?

1. 1. or to a document and user view within the current file.
2. Click a surface on the model. A surface is highlighted when the pointer is properly positioned.
3. Click another surface on the model.
4. Drag the label into position and click once.
5. Click Stop when you're finished taking measurements; at this point, you can still copy the most recent measurement to the WIndows clipboard. Select Close (or X) to end the command and close the dialog box.

1. Open the Angular menu on the 3D Document Toolbar. (How? Click the drop-down arrow to the right of the Angular icon. You should see a drop-down menu listing the available commands.)
2. Select Two Points Draft Angles to view the Two Points Draft Angles dialog box.
3. Optional: If you want to measure more than one angle, select the Lock tool checkbox.Optional: Navigate to or enter
   1. Select Lock tool to use the command more than once.
   2. Enter a hyperlink to a file
   , an Internet page, a user view, or another document in the workspace.

Glen: When I use the browser, system crashes. How is this command used? When the other file is opened, do you then use Copy to transfer measurement info?

1. 1. or to a document and user view within the current file.
2. By default, the Two Points Draft Angles command measures the angle along the Z-Axis. To choose another axis, click the appropriate radio button in the Two Points Draft Angle Measurement dialog box.
3. Click two points on the model. The second point you select will be the vertex of the angle.
4. Drag the label into position and click once.
5. Click Stop when you're finished taking measurements; at this point, you can still copy the most recent measurement to the WIndows clipboard. Select Close (or X) to end the command and close the dialog box.

1. Open the Angular menu on the 3D Document Toolbar. (How? Click the drop-down arrow to the right of the Angular icon. You should see a drop-down menu listing the available commands.)
2. Select Surface Draft Angle to open the Surface Draft Angle dialog box.
3. Optional: If you want to measure more than one angle, select the Lock tool checkbox.Optional: Navigate to or enter
   1. Select Lock tool to use the command more than once.
   2. Enter a hyperlink to a file
   , an Internet page, a user view, or another document in the workspace.

1. 1. or to a document and user view within the current file.
2. By default, the Surface Draft Angle command measures the angle along the Z-Axis. To choose another axis, click the appropriate radio button in the Surface Draft Angle Measurement dialog box.
3. Click a surface on the model.
4. Drag the label into position and click once.
5. Click Stop when you're finished taking measurements; at this point, you can still copy the most recent measurement to the WIndows clipboard. Select Close (or X) to end the command and close the dialog box.